Everything about Dot Pitch totally explained
Dot pitch (sometimes called
line pitch,
phosphor pitch or
pixel pitch) is a specification for a
computer display,
computer printer,
image scanner or other
pixel-based device that describes the distance, for example, between dots (
sub-pixels) of the same color on the inside of a display screen. In the case of a color display dot pitch is a measure of the size of a
triad plus the distance between the triads.
Dot pitch may be measured in linear units, usually
millimetres, with a smaller number meaning closer spacing, or in dots per linear unit, for example
dots per inch, with a larger number meaning wider spacing. Closer spacing generally produces a sharper image (as there are more pixels in a given area). However, other factors may affect image quality, including:
- measurement method not documented, complicated by general ignorance of the existence of multiple methods
- pixel spacing varying across screen area (for example, increasing in corners compared to center)
- differing pixel geometries
- differing screen resolutions when attempting to judge picture quality
- tightness of electron beam focus and aim (in CRTs)
- differing aspect ratios
Traditionally, dot pitch in displays has been measured on the diagonal, as this gives the most accurate representation of image quality. Starting about the mid-
1990s, however, some companies introduced a
horizontal dot pitch as a marketing ploy . By measuring only the horizontal component of the dot pitch and ignoring the vertical component, even a cheap, low-quality monitor could be awarded a small-seeming dot pitch.
The exact difference between horizontal and diagonal dot pitch varies with the design of the monitor (see
pixel geometry and
widescreen), but a typical entry-level 0.28 mm (diagonal) monitor has a horizontal pitch of 0.24 or 0.25 mm, a good quality 0.26 mm (diagonal) unit has a horizontal pitch of 0.22 mm. The smallest dot pitch at the current time is 0.099 mm.
The above dot pitch measurement don't apply to
aperture grille displays. Such monitors use continuous vertical phosphors band on the screen, so the vertical distance between scan lines is limited only by video input signal's vertical resolution and the thickness of electron beam, so there's no vertical 'dot pitch' on such devices. Aperture grille only has horizontal 'dot pitch', or otherwise known as 'stripe pitch'.
Common dot pitches in monitors
LCD screens larger than 15 inches>
| Display resolution |
Megapixel |
Aspect Ratio |
Screen size |
Pixel pitch |
Pixels per inch |
| 1024×768 (XGA) |
0.78 |
4:3 |
15 in |
0.297 mm |
85.5 |
| 17 |
0.337 |
75.3 |
| 1280×768 (WXGA) |
0.98 |
5:3 |
15.4 |
0.262 |
96.9 |
| 1280×800 (WXGA) |
1.01 |
16:10 |
12.1 |
0.204 |
124.7 |
| 13.3 |
0.224 |
113.5 |
| 14.1 |
0.237 |
107.1 |
| 15.4 |
0.259 |
98.0 |
| 17 |
0.286 |
88.8 |
| 1280×1024 (SXGA) |
1.31 |
5:4 |
17 |
0.264 |
96.2 |
| 18.1 |
0.280 |
90.7 |
| 19 |
0.294 |
86.3 |
| 1440×900 (WXGA+) |
1.29 |
16:10 |
14.1 |
0.211 |
120.4 |
| 15.4 |
0.230 |
110.4 |
| 17 |
0.254 |
100.0 |
| 19 |
0.285 |
89.1 |
| 1400×1050 (SXGA+) |
1.51 |
4:3 |
15 |
0.214 |
118.6 |
| 20.1 |
0.292 |
87.0 |
| 1680×1050 (WSXGA+) |
1.76 |
16:10 |
15.4 |
0.197 |
128.9 |
| 17 |
0.218 |
116.5 |
| 19 |
0.244 |
104.0 |
| 20.1 |
0.258 |
98.4 |
| 21 |
0.269 |
94.4 |
| 22 |
0.282 |
90.0 |
| 1600×1200 (UXGA) |
1.92 |
4:3 |
15 |
0.191 |
132.9 |
| 20.1 |
0.255 |
99.6 |
| 21.3 |
0.270 |
94.0 |
| 1920×1200 (WUXGA) |
2.30 |
16:10 |
15.4 |
0.173 |
146.8 |
| 17 |
0.191 |
132.9 |
| 23 |
0.258 |
98.4 |
| 24 |
0.270 |
94.0 |
| 25.5 |
0.287 |
88.5 |
| 27 |
0.303 |
83.8 |
| 2560×1600 (WQXGA) |
4.09 |
16:10 |
30 |
0.250 |
101.6 |
| 3840×2400 (WQUXGA) |
9.21 |
16:10 |
22.2 |
0.125 |
203.2 |
Bolded screen sizes indicate primarily laptop use.
Common dot pitches in printers
Common dot pitches in scanners
Further Information
Get more info on 'Dot Pitch'.
|
External Link Exchanges
Do you know how hard it is to get a link from a large encyclopaedia? Well we're different and will prove it. To get a link from us just add the following HTML to your site on a relevant page:
<a href="http://dot_pitch.totallyexplained.com">Dot pitch Totally Explained</a>
Then simply click through this link from your web page. Our crawlers will verify your link, extract the title of your web page and instantly add a link back to it. If you like you can remove the words Totally Explained and embed the link in article text.
As long as your link remains in place, we'll keep our link to you right here. Please play fair - our crawlers are watching. Your site must be closely related to this one's topic. Any kind of spamming, dubious practises or removing the link will result in your link from us being dropped and, potentially, your whole site being banned. |
